Multipath IO Configuration - Revision history

Qadmin: Point to the Windows MPIO page for failover clusters and Hyper-V

2026-10-06T15:58:54Z

Point to the Windows MPIO page for failover clusters and Hyper-V

← Older revision		Revision as of 15:58, 6 October 2026
Line 30:		Line 30:

	=== Configuring Microsoft MPIO ===		=== Configuring Microsoft MPIO ===
			''For Windows Server failover clusters, Cluster Shared Volumes and Hyper-V on QuantaStor HA pools, see [[Windows MPIO for Failover Clusters and Hyper-V]] for the recommended MPIO setup and timer tuning; the steps below cover only adding the QuantaStor device string.''

	The first step in configuring MPIO on Windows Server is to navigate to MPIO properties. (Note that desktop versions of Windows such as XP, Vista, and Windows 7/8 do not support MPIO, you must be using Windows Server 2003/2008/2012) The easiest way to get to the MPIO configuration screen is to type MPIO in the ''Start'' menu search bar. It can also be found in the Control Panel under "MPIO".		The first step in configuring MPIO on Windows Server is to navigate to MPIO properties. (Note that desktop versions of Windows such as XP, Vista, and Windows 7/8 do not support MPIO, you must be using Windows Server 2003/2008/2012) The easiest way to get to the MPIO configuration screen is to type MPIO in the ''Start'' menu search bar. It can also be found in the Control Panel under "MPIO".

Qadmin at 10:24, 11 August 2025

2025-08-11T10:24:11Z

← Older revision		Revision as of 10:24, 11 August 2025
Line 1:		Line 1:
			== Understanding MPIO with QuantaStor ==
	QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).		QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).

Qadmin at 10:23, 11 August 2025

2025-08-11T10:23:23Z

← Older revision		Revision as of 10:23, 11 August 2025
Line 1:		Line 1:
	~~[[index.php?title=Category:User guide]]~~
	QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).		QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).

Qadmin at 10:23, 11 August 2025

2025-08-11T10:23:12Z

@@ Line 1: / Line 1: @@
-[[Category:user_guide]]
+[[index.php?title=Category:User guide]]
 QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver.  Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).
@@ Line 42: / Line 42: @@
 Note that the '^' characters are provided here so that you can see where the spaces are.  Note also that these are all capital letters, '''with one space between the words, and exactly six trailing spaces after QUANTASTOR.''' If you don't have exactly (6) trailing spaces then the MPIO driver won't recognize the QuantaStor devices and you'll end up with multiple instances of the same disk in Windows Disk Manager.
 === VMWare Special Note ===
@@ Line 136: / Line 134: @@
 Remember, you'll need to make sure that you mount your filesystems using the correct unique device ID under ''/dev/mapper/'' so that the multipath driver is utilized.  If you mount your filesystem from /dev/sdXX you'll have completely bypassed the multi-path driver and will not get the performance an fail-over capabilities.

Qadmin at 05:15, 24 April 2023

2023-04-24T05:15:15Z

← Older revision		Revision as of 05:15, 24 April 2023
Line 97:		Line 97:
	path_checker tur		path_checker tur
	rr_weight uniform		rr_weight uniform
	}		}

	</pre>		</pre>

Qadmin at 05:13, 24 April 2023

2023-04-24T05:13:39Z

@@ Line 42: / Line 42: @@
 Note that the '^' characters are provided here so that you can see where the spaces are.  Note also that these are all capital letters, '''with one space between the words, and exactly six trailing spaces after QUANTASTOR.''' If you don't have exactly (6) trailing spaces then the MPIO driver won't recognize the QuantaStor devices and you'll end up with multiple instances of the same disk in Windows Disk Manager.
 === Configuring Linux Device-Mapper Multipath (DMMP) ===
@@ Line 75: / Line 80: @@
                  path_checker            tur
+         }
 </pre>

Qadmin at 01:29, 22 March 2019

2019-03-22T01:29:23Z

← Older revision		Revision as of 01:29, 22 March 2019
Line 1:		Line 1:
	[Category:user_guide]]		[[Category:user_guide]]
	QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).		QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).

Qadmin: Created page with "[Category:user_guide]] QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver...."

2019-03-22T01:28:59Z

Created page with "[Category:user_guide]] QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver...."

New page

[Category:user_guide]]
QuantaStor supports round-robin style active/active multipathing using Microsoft's MPIO and via Linux using the device-mapper multipath (dmmp) driver. Active/active multipath support not only boosts performance, it also gives you the benefit of automatic path failover when a network connection is lost to one of your NICs on the host (initiator side) or the storage system (target side).

iSCSI Multipathing should be configured using IP's on different network subnets/vlans to ensure proper communication of the paths. Using the same subnet with multiple IP's will not provide a proper multipathing config. QuantaStor will present out iSCSI communication on any iSCSI enabled interface by default, there is no additional configuration required inside QuantaStor to enable path(s) for iSCSI Multipathing other than configuring the network interface with an appropriate IP address and subnet.

e.g. the below example networking configuration would provide two network paths between the QuantaStor and the Host connecting to the QuantaStor.

<pre>
QuantaStor server IP configuration

10.0.1.121/24
10.0.2.121/24

Host Client IP Configuration

10.0.1.125/24
10.0.2.125/24
</pre>

Once the Network configuration is correct, the appropriate Multipathing configuration will need to be performed on the Host Client side, the rest of this section details how to configure Multipathing for the most popular client operating systems.

For Microsoft MPIO configuration you'll need to add the QuantaStor vendor / model information so that Microsoft's default DSM (device specific module) can detect QuantaStor volumes and automatically enable multipathing for them thereby combining multiple paths to your QuantaStor Storage System in a single device as seen in the Windows Disk Manager.

For Linux, you'll need to first install dmmp for your Linux distribution, and then modify the /etc/multipath.conf file to include an additional stanza so that the system properly identifies the QuantaStor devices and uses the correct multi-path device identification and path management rules.

<pre>
Note: QuantaStor supports SCSI-3 Persistent Reservations so you can use it with Microsoft's Failover Clustering / Hyper-V and other cluster solutions that require SCSI-2 or SCSI-3 reservations.
</pre>

=== Configuring Microsoft MPIO ===
The first step in configuring MPIO on Windows Server is to navigate to MPIO properties. (Note that desktop versions of Windows such as XP, Vista, and Windows 7/8 do not support MPIO, you must be using Windows Server 2003/2008/2012) The easiest way to get to the MPIO configuration screen is to type MPIO in the ''Start'' menu search bar. It can also be found in the Control Panel under "MPIO".

[[File:mpio.png|frame|center|The string you will want to add for QuantaStor is "OSNEXUS QUANTASTOR      ". ]]

Once you're at the MPIO dialog, select the "MPIO Devices" tab and then click the "Add" button. The string you will need to add for QuantaStor is exactly:

<pre>
OSNEXUS QUANTASTOR
^ ^^^^^^
</pre>

Note that the '^' characters are provided here so that you can see where the spaces are. Note also that these are all capital letters, '''with one space between the words, and exactly six trailing spaces after QUANTASTOR.''' If you don't have exactly (6) trailing spaces then the MPIO driver won't recognize the QuantaStor devices and you'll end up with multiple instances of the same disk in Windows Disk Manager.

=== Configuring Linux Device-Mapper Multipath (DMMP) ===

After you have device mapper installed on your Linux distribution, you'll need to login to your system as root and then add this section to your ''/etc/multipath.conf'' file for CentOS:

<pre>
device {
vendor "OSNEXUS"
product "QUANTASTOR"
getuid_callout "/sbin/scsi_id -g -u -s /block/%n"
path_grouping_policy multibus
failback immediate
path_selector "round-robin 0"
rr_weight uniform
rr_min_io 100
path_checker tur
}
</pre>

On Ubuntu/Debian the 'getuid_callout' part is a little different so use this version for Ubuntu:

<pre>
device {
vendor "OSNEXUS"
product "QUANTASTOR"
getuid_callout "/lib/udev/scsi_id --whitelisted --replace-whitespace --device=/dev/%n"
path_grouping_policy multibus
failback immediate
path_selector "round-robin 0"
rr_weight uniform
rr_min_io 100
path_checker tur
}
</pre>

Please Note: Starting with the 0.5 release of the linux multipath tools, an additional ''property "(ID_SCSI_VPD|ID_WWN|ID_SERIAL)"'' definition needs to be added to the definitions in the blacklist_exceptions portion of the multipath.conf file.

<pre>
blacklist_exceptions {
property "(ID_SCSI_VPD|ID_WWN|ID_SERIAL)"
device {
vendor "OSNEXUS"
product "QUANTASTOR"

}
}
</pre>

Once the file is updated you'll want to restart the multipath service like so:

<pre>
service multipathd restart
</pre>

Once you have it all configured and you're logging into the iSCSI target / storage volume with your iSCSI initiator you'll want to run 'multipath -l' to list the paths and you should see something like this:

<pre>
14f534e455855530038323061623737393365306365643738dm-2 OSNEXUS,QUANTASTOR
[size=512M][features=0][hwhandler=0]
\_ round-robin 0 [prio=0][active]
\_ 120:0:0:0 sdg 8:96 [active][undef]
\_ 119:0:0:0 sdf 8:80 [active][undef]
14f534e455855530038323061623737393735393231656332dm-1 OSNEXUS,QUANTASTOR
[size=4.0G][features=0][hwhandler=0]
\_ round-robin 0 [prio=0][active]
\_ 118:0:0:0 sde 8:64 [active][undef]
\_ 117:0:0:0 sdc 8:32 [active][undef]
</pre>

Remember, you'll need to make sure that you mount your filesystems using the correct unique device ID under ''/dev/mapper/'' so that the multipath driver is utilized. If you mount your filesystem from /dev/sdXX you'll have completely bypassed the multi-path driver and will not get the performance an fail-over capabilities.